Home > Dvd Drive > DVD Writer Replacement

DVD Writer Replacement

Contents

im not trying to make mine SUPER thin, but ive been piecing together a project by swapping out componants (HDD, ports, adding wireless adapter, etc.) but wanting a little more than Copyright 2011 by Morris Rosenthal All Rights Reserved Replacing a DVD or CD Drive Copyright 2011 by Morris Rosenthal -All Rights Reserved contact info Illustrated How to Replace a CD Drive Comments? You can put the power and audio plugs in from the left and right side. . have a peek here

Be careful not to slide skin along any interior metal edge of the computer. Then find the laser that coincides with your brand. Offers subject to credit approval and may be changed without notice. Figure : IDE cable Slave connector (or second drive) Master connector (first drive) If the IDE cable was removed from the motherboard, connect the other end of the IDE cable into

How To Remove A Cd Drive From My Computer

Test the new drive; see if it can read a CD / DVD. * There are some cases that require the sides to be on before it will power on. Remove the sides of your PC by taking out the screws at the back of the case and sliding the sides backwards (illustration A). Remember where each cable and connector goes because you must reconnect them to the new drive. Click the Hardware tab, and then click the Device Manager button.

  • Since the faceplate of the CD recorder will open to front of the case, it's important (for aesthetics) to make sure it's flush with the front facade before tightening the four
  • You might need to remove the other side panel to access the front cover.
  • Power the computer on.
  • but the xbox is best used with XBMC (formerly XBox Media Center, as it is now avaliable on Windows, Mac, and Linux computers as well).

The 40 wire IDE ribbon cable may be keyed to the connector on the CD burner, or you may be able to force it on backwards. Here is how to tell which kind of drive you have:

http://forums.xbox-scene.com/index.php?s=52bacc3acb1b49745ff19a456919095c&showtopic=17216&view=findpost&p=247188
It's not clear on if you can use any DVD drive, or if it has to be an xbox Finally, the power connector (below) is seated firmly over the four large pins in the connector, usually goes in about a half an inch. Internal Dvd Drive Ask the community!

Using the screwdriver, apply light pressure to one side of the bay insert while pulling it out slightly. How To Remove Dvd Drive From Laptop note: Your computer case is probably different than the computer in the video. Step 1: Removing the drive from Device Manager If you are replacing an existing drive, before removing In other words , are any software changes neededWell this is the only xbox orginal dvd related guide, what i want to do is make my xbox dvd drive run on If a new drive was installed, see the instructions that came with the drive.

Unplug the power cable. Internal Dvd Drive Price then there are MANY PC drives you can use with no "$40 mod unit" and no need to leave another drive hooked up(although i have never heard of that at all)Now The drives are always removed and installed through the front of the case, since the CD tray has to be accessible through the front. Click the Device Manager tab.

How To Remove Dvd Drive From Laptop

If you've forgotten to disconnect the power, IDE or audio patch cables from the back of the DVD drive, you'll find out at this point when it doesn't pull out easily:-) https://www.theguardian.com/lifeandstyle/2010/jan/18/repair-replace-cd-dvd-drive Z7_3054ICK0KGTE30AQO5O3KA3016 hp-feedback-input-portlet Actions ${title} Loading... How To Remove A Cd Drive From My Computer They should unclip or unscrew fromthe old drive and can be fitted to the new drive in the same position. Replacement Dvd Drive For Laptop Replace the screws in the side of the drive and replace the front of the case if necessary.

Marked on the DVD/CD it will show a small diagram with 3 options - Slave, Master and Cable Select (CBL). navigate here We remove all of the plug in connectors from the back of the DVD drive (see the later pics of making connections) and remove the four fine thread screws. If so, unclip them as you pull. The CD burner is then installed in the case, and secured with four screws. How To Remove Dvd Drive From Hp Pavilion Desktop

Keep the screws because you will need them later. The second connector is the IDE cable, it’s very wide. Both of them only fit one way -- the right way. 3Remove the old drive, if necessary, by unplugging its power and data cables, unscrew the drive from the case or Check This Out Write a guide cdnerd Explore more guides View previous The Complete DVD Drive Buying Guide Image The Complete DVD Drive Buying Guide Published by: eBay DVD-ROM Drive Buying Guide Image DVD-ROM

Connect the power cable and sound cable (if used), into the back of the drive. Removing Cd/dvd Drive Take the sides off the computer. What you will need. 1.

Visit now Z7_3054ICK0KGTE30AQO5O3KA30H4 hp-feedback-banner-portlet Actions ${title} Loading...

the process is not hard. What is the cost for the xbox specific drive? Country: United States Select a location Americas Europe, Middle East, Africa Asia Pacific and Oceania Select a language Confirm Back Z7_M0I02JG0KOT530A6KJKFRQ0816 hp-detect-load-my-device-portlet Actions ${title} Loading... Remove Virtual Cd Drive If they will not come out, check that there are no clips or blobs of glue holding them in place.

Step 3. But for the same money you can just get a XBox DVD drive....sometimes you will have BIOS issuesengineeringIf anyone compare the price of any new one xbox dvd .........then If more than one bay is available, it doesn't matter which bay you mount the drive in, though I favor lower bays for a lower center of gravity and shorter cable this contact form This is on the far side of the DVD drive and should be a little black plug with a clip at the top.

Each is hidden under stickers or the padded feet on the case. 2 Step 2: Take out the old driveTo remove the old drive, simply remove 2 #10 Torx screws from To reduce the chance of ESD damage, work over a noncarpeted floor, use a static dissipative work surface (such as a conductive foam pad), and wear an ESD wrist strap connected Now that all the wires are out, look for the screws that are holding the drive in place. With the power cable removed, press the Power button on the front of the computer.

Once removed put them in the bowl so you don’t lose them. Congratz your done - you just saved yourself time and cash. The easiest to ensure a newly installed DVD burner will be addressed properly is to put it next to the old CD drive and make sure the same jumper pair is Some times games wouldn't load and I would get the "dirty disc error." After Googling those symptoms, it appeared I had a bad drive.




© Copyright 2017 revolutionpc.net. All rights reserved.